Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
November — 2003 — The Pipe Supports Blog
Archive for November, 2003

60" diameter Flue Gas Duct

November 21st, 2003 No comments

60" diameter Flue Gas Duct

60" diameter Flue Gas Duct

Sweco Fab, Inc. designed and manufactured a Flue Gas Duct, weighing over 66,000 lbs. and 18′-5 in length, for an oil refinery in Detroit, Michigan. The duct is designed to transport hot gases from the regenerator to the flue gas cooler. The walls are 1/2 thick with a high-density vibracast refractory lining. The rest of the unit was fabricated out of carbon steel SA-516-70 and is designed for a maximum pressure of 51 PSIG and maximum temperature of 1450°F.

Leak examinations where performed on the unit after fabrication, which included a10 percent x-ray test, a100 percent dye-pen test and a hydrotest at 77 PSIG.

Do you require a flue gas duct in your current or future job? Get pricing today!
request-a-quote


Three Segments 120° 72” diameter Saddle Support with Neoprene Backing

November 14th, 2003 No comments
Three Segments 120° 72” diameter Saddle Support with Neoprene Backing

Three Segments 120° 72” diameter Saddle Support with Neoprene Backing

PT&P fabricated various sized saddle supports used to support water mains for the city of Houston.  The pipe saddles, ranging from 30”-72” in length and 12” in width are made to cover 1/3 of the pipe’s circumference. They are made of A-304 stainless steel with a neoprene backing.

These saddles are used to provide a sliding surface between metal water mains and concrete base supports at fault crossings. The neoprene backing helps to dissipate any shock loads and provides an anti-skid surface at the fault crossing locations.

Do you require pipe saddles in your piping system? Get pricing today!

request-a-quote


PTP-6 Carbon Steel Variable Springs

November 7th, 2003 No comments
PTP-6 Carbon Steel Variable Springs

PTP-6 Carbon Steel Variable Springs

PT&P recently designed and manufactured PTP-6 Type G variable springs in size PTP 6-00-G for a power plant project in Colorado.  These variable springs are constructed from carbon steel with movement ranging from 1” to 2” and loads of 73 lbs and 52 lbs, respectively. They were tested prior to shipping for load and movement performance by using calibrated load cells.

Do you see a need for variable springs in your piping system? Get pricing today!


request-a-quote


November 2003 News

November 4th, 2003 No comments

Adjustable & Welded Instrument Components

Instrument Supports

Instrument Supports

Instrument Supports

Cable Mount

Piping Technology & Products, Inc. offers a complete line of adjustable and welded instrument supports in various mounting styles. Our instrument supports may be used independently or with secondary components to construct a custom support system. please refer to our catalog for details and ordering information.

Instrument Supports

U-bolt Mount

instrument support

Floor Mount

Do you require instrument components in your current or future job? Get pricing today!

request-a-quote


Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy