Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
April — 2008 — The Pipe Supports Blog
Archive for April, 2008

90" O.D. Duct Work for an Ammonia Plant

April 25th, 2008 No comments

90" O.D. Duct Work for an Ammonia Plant

90" O.D. Duct Work for an Ammonia Plant

90" O.D. Duct Work for an Ammonia Plant

90" O.D. Duct Work for an Ammonia Plant

The duct work has an outside diameter of 90 inches and is 38 feet long. The duct assembly is fabricated entirely from ASTM A516-70 carbon steel. The assembly has two support bases and stiffening rings that provide strength and rigidity for the duct work. The assembly is a section of air supply duct in an Ammonia Plant.

Do you require duct work for your piping system? Get pricing today!
request-a-quote

63″ x 63″ Big Ton Springs for an Oil Refinery

April 14th, 2008 No comments
63" x 63" Big Ton Springs for an Oil Refinery

63" x 63" Big Ton Springs for an Oil Refinery

The base measures 63 inches square while the top load flange measures 55 inches square. One of the springs has an overall height of 22-7/16″ and the other an overall height of 28-5/8″. Both big ton springs are custom designed and fabricated from carbon steel with a hot-dipped galvanized finish. The top of the load flange is covered by a stainless steel slide plate. These big ton springs will be used to support heavy (in excess of 100,000 lb.) loads where a standard variable spring would be undersized.

One of the big ton springs is designed with a operating load of 126,000 lb. and the other with an operating load of 225,000 lb. Prior to fabrication, all of the coils, within the frame, were individually tested to insure correct spring rate and load capacity. After the units are fabricated, the entire assembly is tested throughout the entire load/travel range.

Do you require a similar spring support in your piping system?  Let us price it for you now! 
request-a-quote

Polyurethane Saddle Supports for FRP Pipe

April 2nd, 2008 No comments
Polyurethane Saddle Supports for FRP Pipe

Polyurethane Saddle Supports for FRP Pipe

Polyurethane Saddle Supports for FRP Pipe

Polyurethane Saddle Supports for FRP Pipe

Piping Technology & Products, Inc. designed and fabricated these saddle supports to support FRP pipe or similar plastics in sizes from 2″ to 36″ in diameter. The saddle support is fabricated from a molded density 20 polyurethane block with a load bearing capacity of 150 PSI that allows for high loads for a 36″ diameter line.

The base is bonded to a 20 gauge steel pan that provides a steel to steel resting surface. The foam is extended on each side of the base to allow field strapping of the support to the pipe. These saddle supports are often used in a circulating water service. These particular supports are to be used in a power generating station in the U.S.

Do you require similiar saddle supports for your application? Let us price them for you!
request-a-quote

Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy