Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
May — 2017 — The Pipe Supports Blog
Archive for May, 2017

High Temperature Insulated Supports for an HP Steam Header

May 30th, 2017 Comments off

High Temperature Insulated Supports for an HP Steam Header

Type: Pre-Insulated Pipe Supports for High Temperatures “Hot Shoes”
Size: 2″ – 12″ dia. | 12″, 15″, 18″ Long | 4″ and 6″ BOP
Material: Carbon Steel with Thin Blanket Insulation
Testing: Standard Q.C. Inspection | ANSYS Simulation

Piping Technology & Products custom designed and fabricated pre-insulated pipe supports for high temperature application in an HP Steam Header located in Texas. These hot shoes range in size from 2″ to 12″ in diameter and are 12″, 15″ and 18″ long, with BOP of 4″ and 6″. The supports include a thin blanket insulation. The trunnion assembly is resting on a high compressive strength insulation material. These supports are designed for temperatures up to 844°F with an operating load of 17,965 lb. at 732 psig. A total of 95 supports were manufactured for this project, including pipe hangers, pipe shoes with insulation and trunnion supports, as well as pipe shoe clamps without insulation. All supports were inspected by Q.C. and the insulated supports underwent a simulation on ANSYS.

Structural Supports Custom Designed for a Liquefaction Project

May 22nd, 2017 Comments off

Structural Supports Custom Designed for a Liquefaction Project

Type: Structural Supports
Size: 6″ x 12″ to 6″ x 18″
Material: Carbon Steel with HDG Finish
Testing: Standard Q.C. Inspection

Piping Technology & Products custom designed these structural supports to provide base support for pipes at a liquid natural gas (LNG) facility in Louisiana. The supports are fabricated from carbon steel with a hot-dipped galvanized finish. Sizes range from 6″ x 12″ to 6″ x 18″ and all supports underwent a quality control inspection prior to shipment.

Mechanical Snubbers for a Refinery in Oklahoma

May 5th, 2017 Comments off

Mechanical Snubbers for a Refinery in Oklahoma

Type: Mechanical Snubbers
Size: Size MSA-10, 36″ OAL, and 30 1/2″ Pin-To-Pin
Material: Carbon Steel with HDG Finish
Design: Operating load of 15,000 lbs and a 6″ Maximum Stroke
Testing: Standard Load Tests

Piping Technology & Products supplied these mechanical snubbers with two end brackets, fabricated from carbon steel with an HDG finish for a refinery in Oklahoma. They are size MSA-10, 36″ OAL, and 30 1/2″ pin-to-pin. The snubbers are designed for an operating load of 15,000 lbs and have a 6″ maximum stroke. Standard load tests were performed prior to shipment. Mechanical snubbers have two modes of operation. In passive mode, i.e., motion caused by thermal loads, the resisting mechanism is disengaged and the snubber “free wheels” with very low resistance. In active mode the mechanism is engaged, and the snubber limits the acceleration to a low threshold value.

PT&P Cryogenic Blanket Insulation Prototype Test

May 2nd, 2017 Comments off

Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy