Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
Ray — The Pipe Supports Blog
Author Archive

Insulated Pipe Supports

April 29th, 1994 No comments
Insulated Pipe Supports

Insulated Pipe Supports

The photographs above show insulated pipe supports designed for a system being installed in a very cold climate in Russia. The insulating components are inside next to the pipe. The outside components are galvanized steel. In the foreground of the photo at the right are two fixtures which were built for load testing these pipe supports by applying known forces with a hydraulic load cell. Piping Technology & Products, Inc., fabricated prototype units for a Houston Engineering Firm and tested the units. After successful tests a number of similar units were built for shipment to Russia.

In need of some new insulated pipe supports? Let us price one for you today!

request-a-quote


Launcher and Receivers

April 22nd, 1994 No comments

 

Launcher and Receivers

Launcher and Receivers

The photograph above shows a launcher-receiver designed to be installed in a six inch pipe to launch and receive pipeline pigs. Pigs can be used for cleaning or for separation of two products in the same pipeline. This launcher-receiver was one of two built by the SWECO Fab, Inc. division of Piping Technology & Products, Inc. for a major Gulf Coast Refinery.

Would you like to learn more about our pig launcher and receivers? Visit our webinar archives today!

access-our-webinar-archives

Arrestor Type Hold Down

March 9th, 1994 No comments
Arrestor Type Hold Down

Arrestor Type Hold Down

The above photo shows an arrestor type hold down. This type of restraint is used when there is very low thermal movement. Its radius is lined with a belting material designed to absorb shock from movement. It is widely used on compressor lines or similar applications. The restraint type hold down’s clamp radius and base is lined with PT&P’s PTFE slide plate which allows for axial movement while restraining lateral movement and used on compressor lines where temperatures are high and thermal movement is great. This anchor type hold down is utilized on pipelines and require little or no insulation. It is fabricated from carbon steel and can be used in temperatures up to 750oF.

Would you like to learn more about hold down clamps and slide plates? Visit our website archives today!

access-our-webinar-archives

Specially Designed and Fabricated Tanks

March 9th, 1994 No comments
Specially Designed and Fabricated Tanks

Specially Designed and Fabricated Tanks

Shown above is one of three neutralization tanks engineered and fabricated by Sweco Fab, Inc. This particular tank is being shipped to the paint contractor for painting and special interior coating.

These tanks are 12 feet in diameter, 39 feet 7 inches high, and have a storage capacity of 25,000 gallons. Special features requested by the client include clips welded on the interior for mounting of headers.

Do you require a tank or vessel for an upcoming project? Let us price it for you today!

request-a-quote

Constant Effort Supports for Generating Facilities

March 8th, 1994 No comments
Constant Effort Supports for Generating Facilities

Constant Effort Supports for Generating Facilities

Constant Effort Supports for Generating Facilities

Constant Effort Supports in the Field

Piping Technology & Products, Inc. has designed and built thirty-two constant effort supports ranging in loads from eighty to eighty-seven kips with seven and one half inches of total travel on each.Six of the thirty-two are shown in position and they will support critical portions of the heater. The balance in other parts of the plant will support equally critical lines such as main steam and boiler reheat.

Located near Calvert, Texas, this is the second generating facility for Texas – New Mexico Power at this site. Piping Technology & Products, Inc. supplied the same material on the previous installation for this client.

Learn more about our constant supports, visit the webinar archive today!

access-our-webinar-archives

Spectacle Blinds for 60” Pipe

March 4th, 1994 No comments

 

Spectacle Blinds for 60” Pipe

Spectacle Blinds for 60” Pipe

Pictured above are spectacle blinds. Piping Technology & Products, Inc. builds these for any pipe size up to 60”. A variety of metals can be used including carbon steels, stainless steels or exotic alloys depending on the pressure rating required and the environment where they must function.

Do you need any spectacle blinds for an upcoming project? Let us price it for you today!

request-a-quote

Removable Pipe Supports

February 11th, 1994 No comments
Removable Pipe Supports

Removable Pipe Supports

The photograph above shows one of 72 of these supports fabricated by Piping Technology & Products, Inc. for shipment to Alaska. Note that the distance between the top pipe where other components are attached and the base the support rests on can be changed by selecting the holes for the arms. These removable supports are used during installation of pipelines. Pipe sections may have other permanent supports if the pipe is above ground or the lines may be underground.

Would you like to learn more about pipe supports? Visit out webinar archives today!

access-our-webinar-archives

Constants for a Radiant-tube Support System

January 8th, 1994 No comments
Constants for a Radiant-tube Support System

Constants for a Radiant-tube Support System

The photograph above shows a large number of specially designed constant spring supports being prepared for shipment to Chile. These constants are the key component of a reforming furnace, radiant tube support system designed for one of the world’s major engineering and construction firms.

Piping Technology’s engineers designed these units to fit in the limited space available inside the furnace and provided optional bolting patterns so attachment to the supporting structure could be made even if the radiant tube support system assumed a competitor’s design.

Do you require constant spring supports in an upcoming project? Get pricing today!

request-a-quote

Refurbished Constant Supports

December 3rd, 1993 No comments
Refurbished Constant Supports

Refurbished Constant Supports

The picture above shows the “before” and “after” of constant supports refurbished by Piping Technology & Products, Inc. Customers ship these units to our plant during a turn-around in a wide variety of conditions. In this case it was cheaper and faster to refurbish them than to rebuild. In either case each unit is completely tested in a load cell to assure performance and a new name plate is attached to record the load, travel and other parameters. Four of these horizontal upthrust supports can be seen above, ready for return to the customers. Power plants, petrochemical plants and paper mills are the primary users of this service.

Want to learn more about constant supports? Check out our live webinar archives!

access-our-webinar-archives

Flue Gas Duct Damper

November 19th, 1993 No comments
Flue Gas Duct Damper

Flue Gas Duct Damper

The picture above shows a flue gas duct damper fabricated using Inconel for certain components by the Sweco Fab division of Piping Technology & Products, Inc. Two of these dampers were shipped to Trinidad for installation above the furnaces of an ammonia plant. They have a special refractory lining to withstand the high temperatures of the flue gases. The picture at the left show the linkage of the damper to the motor-driven control system. Each unit weighs approximately 2300 lb. and the openings are approximately 12 feet by 6 feet.

Need a duct damper for a future project? Let us price one for you today.

request-a-quote

Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy