Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
Ray — The Pipe Supports Blog
Author Archive

Insulated Pipe Supports Designed for 6″ Dia. Cold Temperature Piping

January 11th, 2014 Comments off

Insulated Pipe Supports Designed for 6

These insulated pipe supports are designed for 6″ diameter cold temperature piping for a gas refinery in Texas. They are fabricated with a carbon steel shell and 5″ thick polyurethane insulation. PT&P offers various types of insulated supports utilizing insulating materials designed for piping ranging in surface temperatures from -460°F to 1,200°F.

72 Bolt Cradle Pipe Supports Designed for a Sulphuric Acid Plant

December 30th, 2013 Comments off

72 Bolt Cradle Pipe Supports Designed for a Sulphuric Acid Plant

PT&P manufactured seventy-two bolt cradle pipe supports for a Sulphuric Acid Plant in Canada. The supports are designed for pipes ranging from 1-1/2″ to 20″ in diameter. They are fabricated from carbon steel and coated with a special protective paint for acid service. Standard bolt cradle supports are offered in 2″ to 24″ diameter pipe sizes; however, PT&P can manufacture any size needed for your application.

112 Custom Variable Springs Designed for a Furnace Application in Venezuela

December 15th, 2013 Comments off

112 Custom Variable Springs Designed for a Furnace Application in Venezuela

112 custom variable springs designed for a furnace application for an oil refinery in Venezuela. The furnace cans are designed from carbon steel and painted with red oxide primer to prevent corrosion when exposed to high temperatures. The sizes of these figures PTP-6 and PTP-8 range in length from 25″- 39″, with a total travel of 0.1″- 1.821″ and loads varying from 430 – 681 lb. A load test to confirm the spring rate was conducted on each assembly prior to shipment.

Pipe Guides Designed for a Recovery Boiler

December 1st, 2013 Comments off

Pipe Guides Designed for a Recovery Boiler

These pipe guides were designed for a recovery boiler in a power plant in Oklahoma. The guides were designed to control lateral pipe movement and maintain the alignment of the piping through its axial and contraction cycles. They were designed to support 6″, 12″ and 18″ pipes and range in length from 70″ – 120″. The assemblies were fabricated from carbon steel with a hot-dipped galvanized finish.

27 B-Type Variable Spring Supports Designed for an Oil Refinery

November 23rd, 2013 Comments off

27 B-Type Variable Spring Supports Designed for an Oil Refinery

PT&P designed and manufactured 27 B-Type variable spring supports for an oil refinery in Louisiana. The spring cans, rods, welded beam attachments, turnbuckles and clevises are fabricated from carbon steel. The spring cans have a 12-3/4″ diameter and measure 290″ from the bottom of the steel to the connection of the pipe. They were designed for 2″ of vertical movement and operating loads between 24,375 and 27,500 lb.

215 Heavy Duty Pre-Insulated Pipe Supports Designed for a High Temperature Application

November 9th, 2013 Comments off

215 Heavy Duty Pre-Insulated Pipe Supports Designed for a High Temperature Application

Pipe Shields Inc., a division of PT&P, manufactured 215 heavy duty pre-insulated supports for a high temperature application in Oregon. They are 15″ L x 20″ W x 31″ H and are designed to accommodate 14″ – 20″ diameter pipes. The hot shoes have a calcium silicate insulation thickness of 2.5″- 3″. The base, clamps, nuts, jackets and bolts are all fabricated from hot dipped galvanized carbon steel and coated with red oxide paint. Standard Q.C. and dimensional tests were performed prior shipment.

282 Instrument Supports Designed for a Six-Drum Coker Unit

October 26th, 2013 Comments off

282 Instrument Supports Designed for a Six-Drum Coker Unit

PT&P designed and manufactured 282 instrument supports to support a six-drum Coker unit in a refinery in Indiana. Some of the assemblies are designed to be bolted by anchor bolts while others are designed to be welded. The supports are fabricated from hot-dipped galvanized carbon steel and measure 11″ – 61″ in height and 5″ – 28″ in width.

Sway Strut and Pipe Clamp Assemblies Designed for a Natural Gas Facility in Canada

October 18th, 2013 Comments off

Sway Strut and Pipe Clamp Assemblies Designed for a Natural Gas Facility in Canada

PT&P designed sway strut and pipe clamp assemblies for a pipeline at a natural gas facility located in Canada. The sway struts are 87-1/2″ in length and the clamps are designed for pipes ranging from 6″ to 42″ in diameter. The assemblies are designed for operating loads ranging between 3,300 lb. to 20,000 lb., with an operating temperature of 392°F and 9mm -20mm of allocated vertical movement. A load test was performed on the assemblies prior to shipment.



42″ Dia. Transition Piece Designed for a Water Tower in Texas

October 6th, 2013 Comments off

42" Dia. Transition Piece Designed for a Water Tower in Texas

Sweco Fab, Inc. (a division of PT&P) custom designed a transition piece weighing 6,000 lb. for a facility in Texas. The piece measures 48″ x 72″ x 72″ and is fabricated from carbon steel. It will be used to connect a round water tower to a square duct. Prior to shipping, the product was 100% dye penetrant tested.

Variable Spring & Graphite Slide Plate Assemblies Custom Designed for Gasoline Production in Dubai

September 21st, 2013 Comments off

Variable Spring & Graphite Slide Plate Assemblies Custom Designed for Gasoline Production in Dubai
In eight weeks, PT&P provided a gasoline production plant in Dubai with two custom designed variable assemblies. Each assembly includes load columns, four variable spring cans, four channels, 12 plates, nine graphite slide plates and a custom designed frame. The frame allows the variable springs to work in unison to support large pipe trunnions. The top plates measure 45″ in width and 25″ in height. The variables are designed for an operating temperature of 750°F and an operating load of 3,150 lb. The assemblies are capable of 1/8″ upward movement and 1/6″ downward movement. A load test was conducted prior to shipment.




Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy