Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
Fabricated Pipe Shoes, Guides and Anchors — The Pipe Supports Blog

Pipe Saddles for a Refinery in Chad

November 27th, 2002 No comments
Pipe Saddles for a Refinery in Chad

Pipe Saddles for a Refinery in Chad

Piping Technology & Products, Inc. designed and manufactured these saddles for a power plant in Chad.

The saddles are comprised of bolt clamps, structural steel and vinyl pipe shields.  They were built for bare pipes ranging in size from 2 24 and can accommodate temperatures from 29 degrees C. to 538 degrees C.

Do you see a need for pipe saddles in your plant or refinery? Let us price them for you today!


request-a-quote


Cylinder Pipe Guides

May 17th, 2002 No comments
Cylinder Pipe Guides

Cylinder Pipe Guides

Cylinder Pipe Guides

Cylinder Pipe Guides

Piping Technology & Products, Inc. designed and manufactured cylinder pipe guides for an energy center in Canada.

These guides, which are frequently referred to as spider guides, are designed to control lateral pipe movement and maintain the alignment of the piping through its axial and contraction cycles. A single piping run uses spider guides in number to avoid a fulcrum or an imposed lateral deflection on critical components.

These spider guides were designed for pipes ranging from 1″ to 20″ diameter with 1″ to 4″ of insulation. The components include carbon steel plates, stock clamps, angles and green-primer coated pipes. The outer shields have diameters ranging of approximately 6″ to 29-1/2″ with a bottom-of-angle to center-of-pipe dimensions of 3-1/8″ to 15-3/4″. The maximum design temperature for the spider guides is 750°F.

Cylinder Pipe Guides for a Power Plant

Cylinder Pipe Guides for a Power Plant

If you need cylinder pipe guides for an upcoming project, request a quote today and receive a response within 48 hours!

request-a-quote


Pipe Shoes with Loads up to 75,000 lb.

March 29th, 2002 No comments
Pipe Shoes with Loads up to 75,000 lb.

Pipe Shoes with Loads up to 75,000 lb.

Piping Technology & Products, Inc. designed and fabricated several pipe shoes with loads up to 75,000 lbs. respectively, for a 750MW power plant in Alabama.

The shoes are to support the cooling towers’ circulatory water system at the power plant. The majority of the shoes were designed for a 60″ line and 50,000 lb. load, and the remaining few were designed for a 78″ line and 75,000 lbs. of load. After extensive engineering hours and structure analysis, PT&P’s engineering department was able to produce a detailed design and 3-D model for the supports that would allow them to run electronic interface checks.

Do you need pipe shoes? Get pricing today!

request-a-quote


Chrome-Moly Shoe for an 18" Pipe

February 22nd, 2002 No comments
Chrome-Moly Shoe for an 18" Pipe

Chrome-Moly Shoe for an 18" Pipe

Piping Technology & Products, Inc., designed and fabricated a Figure 700 chrome-moly shoe for an 18″ pipe used to support high temperature lines at a power plant in Mexicali, Mexico.

The shoe’s length is 12″ and the pipe centerline distance was maintained at 17 3/8″ from the bottom of the shoe. The clamp was designed at 1065°F and the load was designed for 6965 pounds. The base and clamp plates are made of A387 GR.22 plate material and the u-bolt parts are made of A193 GR.B7 bar stock.

Want to learn more about chrome-moly shoes and other products from Piping Technology and Products? Visit our webinar archives today!



access-our-webinar-archives



Pipe Shoes For 14" Pipe At A LNG Plant

November 30th, 2001 No comments
Pipe Shoes For 14" Pipe At A LNG Plant

Pipe Shoes For 14" Pipe At A LNG Plant

Pipe Shoes For 14" Pipe At A LNG Plant

Pipe Shoes For 14" Pipe

Piping Technology & Products, Inc. fabricated cryogenic pipe supports designed for a 14-inch pipe at a LNG plant in Algeria. The pipe operates below minus 50 degrees F, therefore the pipe supports were fabricated from three different materials in order to accommodate the low temperatures. The upper part, which clamps on to the pipe, was fabricated from a stainless steel plate that retains its strength at low temperatures. The middle section is a laminated phenolic block made from layers of wood impregnated under vacuum with a synthetic resin. A crossed orientation of the hard wood fibers is used to provide extra strength. The laminated phenolic block, which is a poor conductor of heat, was bolted to the bottom plate of the galvanized carbon steel.

Are you in need of some cryogenic pipe supports for an upcoming project? Get pricing today!

request-a-quote


High Strength Stainless Steel Pipe Guides

August 23rd, 2001 No comments
High Strength Stainless Steel Pipe Guides

High Strength Stainless Steel Pipe Guides

High Strength Stainless Steel Pipe Guides

LNG Facility in Trinidad

Piping Technology & Products, Inc. manufactured over 2,000 high-strength, stainless steel pipe guides for a liquefied natural gas facility in Trinidad.

This high strength insulation is rare and mainly used for cryogenic applications. The guides range in a variety of sizes including 4-inch to 36-inch NPS and the fabrication included carbon steel base plates and stainless steel plates, nuts and bolts.

Looking for pipe guides? Get pricing today!

request-a-quote


Constants for a Radiant-tube Support System

January 8th, 1994 No comments
Constants for a Radiant-tube Support System

Constants for a Radiant-tube Support System

The photograph above shows a large number of specially designed constant spring supports being prepared for shipment to Chile. These constants are the key component of a reforming furnace, radiant tube support system designed for one of the world’s major engineering and construction firms.

Piping Technology’s engineers designed these units to fit in the limited space available inside the furnace and provided optional bolting patterns so attachment to the supporting structure could be made even if the radiant tube support system assumed a competitor’s design.

Do you require constant spring supports in an upcoming project? Get pricing today!

request-a-quote

Pipe Shoes for Saudi Arabian Oil Company

November 23rd, 1993 No comments
Pipe Shoes for Saudi Arabian Oil Company

Pipe Shoes for Saudi Arabian Oil Company

This photograph shows a number of 60” pipe shoes fabricated by Piping Technology & Products, Inc. of Houston, TX for export to Saudi Arabia. The Saudi Arabian Oil Company is purchasing a variety of sizes of this type of shoe and other items required for piping on their projects. Piping Technology furnishes all types of pipe supports including PTFE, 25% glass filled, and graphite slide plates, anchors and insulated pipe shoes.

Want to learn more about pipe shoes? Learn more from one of our previous webinars!

access-our-webinar-archives

Large Fabricated Pipe Support for a Major Refinery

August 19th, 1993 No comments
Large Fabricated Pipe Support for a Major Refinery

Large Fabricated Pipe Support for a Major Refinery

Large fabricated pipe support being welded by one of Piping Technology’s welders. When it is completed it will be shipped to a major refinery in the Virgin Islands.

Do you need any type of fabricated pipe supports? Allow us to provide a quote!

request-a-quote

Pipe Shoes for Cold Temperature Applications

March 12th, 1993 No comments
Pipe Shoes for Cold Temperature Applications

Pipe Shoes for Cold Temperature Applications

The picture above shows a 54 inch “cold” shoe of galvanized steel with PTFE slide plates on the bottom. Inside the galvanized steel is bonded a layer of polyurethane foam which has been coated with a white vapor barrier. This polyurethane layer provides both insulation and support of the load at cryogenic temperatures..

Do you have an application that requires cold temperature shoes? Get pricing today!

request-a-quote

Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy