Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
Pre-Insulated Pipe Supports — The Pipe Supports Blog

48″ Guided Pre-Insulated Pipe Supports for High Temperatures

June 24th, 2009 No comments
48" Guided Pre-Insulated Pipe Supports for High Temperatures

48" Guided Pre-Insulated Pipe Supports for High Temperatures

Pipe Shields, Inc., a subsidiary of Piping Technology & Products, Inc., designed these pre-insulated supports for a pipe size of 48″. The clamp and base are fabricated from carbon steel that includes a hot dipped galvanized finish. The 4″ thick insulation is a high density calcium silicate. These guided supports allow for a maximum axial travel of plus or minus 4 1/2″ and have a vertical load rating of 7,100 lb. The operating temperature of the pipe may exceed 1,200ºF, therefore the hot shoes are designed for 1,700ºF. These heavy duty base mounted pipe supports are specially designed to be installed on four emergency diesel exhaust mufflers in a hospital.

Do you need hot shoes for your current or future project? Get pricing today!
request-a-quote

84" Pre-Insulated Pipe Support for High Temperatures

September 24th, 2008 No comments
84" Pre-Insulated Pipe Support for High Temperatures

84" Pre-Insulated Pipe Support for High Temperatures

84" Pre-Insulated Pipe Support for High Temperatures

Preparing the Hot Shoe Insulation

Designed for a pipe size of 84″, this pre-insulated pipe support is able to withstand temperatures up to 1,220ºF. It is a wide base sliding hot shoe with up to 2″ of axial travel and 3″ of lateral travel. It can support loads up to 33,721 lb. and the support itself weighs approximately 1,900 lb. This high temperature pre-insulated pipe support will be utilized in a styrene plant.

Want to learn more about pre-insulated supports? Watch a pre-insulated support webinar now!

access-our-webinar-archives

Refractory Lined Pre-Insulated Supports

June 18th, 2008 No comments
Refractory Lined Pre-Insulated Supports

Refractory Lined Pre-Insulated Supports

Refractory Lined Pre-Insulated Supports

Shipping Pre-Insulated Supports

Piping Technology & Products, Inc. designed and fabricated rotational anchor pre-insulated pipe supports for a fluid processing plant in Kuwait. The supports range in size from 24″ to 34″ in diameter and are capable of withstanding 12,500 lb. of vertical load. The bottom of the hot shoe is fabricated from carbon steel and the top from stainless steel.

These supports include stainless steel inner thrust plates that function as an anchor to prohibit the pipe from rotating within the shoe. These supports are designed for steam super heater lines and provide thermal insulation for the pipe in order to prevent heat loss and condensation.

Want to learn more about pre-insulated supports? Instantly watch a pre-insulated support webinar!
access-our-webinar-archives

Polyurethane Saddle Supports for FRP Pipe

April 2nd, 2008 No comments
Polyurethane Saddle Supports for FRP Pipe

Polyurethane Saddle Supports for FRP Pipe

Polyurethane Saddle Supports for FRP Pipe

Polyurethane Saddle Supports for FRP Pipe

Piping Technology & Products, Inc. designed and fabricated these saddle supports to support FRP pipe or similar plastics in sizes from 2″ to 36″ in diameter. The saddle support is fabricated from a molded density 20 polyurethane block with a load bearing capacity of 150 PSI that allows for high loads for a 36″ diameter line.

The base is bonded to a 20 gauge steel pan that provides a steel to steel resting surface. The foam is extended on each side of the base to allow field strapping of the support to the pipe. These saddle supports are often used in a circulating water service. These particular supports are to be used in a power generating station in the U.S.

Do you require similiar saddle supports for your application? Let us price them for you!
request-a-quote

Permali® Cold Shoes for Carbon Steel Pipe

March 12th, 2008 No comments
Permali® Cold Shoes for Carbon Steel Pipe

Permali® Cold Shoes for Carbon Steel Pipe

These cold shoes are anchors supports and fabricated with A-36 carbon steel and permali® block insulation. The carbon steel is hot-dipped galvanized for protection and longevity of the cold shoe. The permali® block insulation, between the base plate and the saddle, functions to insulate the supporting structure from extreme cold temperatures of the pipe.

These cold shoes are designed for pipes ranging in size from 6″ to 14″. The assemblies are capable of loads ranging from 194,000 lb. to 291,000 lb.

Want to learn more about pre-insulated supports? Instantly view a past webinar today!


access-our-webinar-archives



24" Heavy Duty Cryogenic Pipe Supports

February 6th, 2008 No comments
24" Heavy Duty Cryogenic Pipe Supports

24" Heavy Duty Cryogenic Pipe Supports

24" Heavy Duty Cryogenic Pipe Supports

24" Heavy Duty Cryogenic Pipe Supports

These pipe supports were designed for a petrochemical plant in Puerto Rico. The nominal pipe size of the supports ranges between 16″ and 24″. The cryogenic supports are fabricated from carbon steel and include a stainless steel jacket. They are insulated with polyurethane foam and are designed for temperatures between -270ºF and 85ºF. The load capacity ranges between 5,000 lb. and 11,900 lb.

Want to learn more about cryogenic pipe supports? Instantly view a past webinar!

access-our-webinar-archives

36" Cold Shoe Anchors for an LNG plant in Louisiana

November 28th, 2007 No comments
36" Cold Shoe Anchors for an LNG plant in Louisiana

36" Cold Shoe Anchors for an LNG plant in Louisiana

 

36" Cold Shoe Anchors for an LNG plant in Louisiana

36" Cold Shoe Anchors for an LNG plant in Louisiana

These cold shoe anchors are designed to support pipe sizes ranging from 8″ to 36″ in diameter. The measurements of the base plate are between 18″ and 36″ in length and between 8″ and 22″ in width. The saddle is fabricated from stainless steel and the base plate is galvanized steel. Micarta insulation material, between the base plate and the saddle, functions to insulate the extremely cold pipeline. These cold shoe anchors are manufactured for large axial and lateral capacities.

Want to learn more about pre-insulated pipe supports? View a pre-insulated pipe support webinar today!


access-our-webinar-archives



Base Insulated Supports

October 31st, 2007 No comments
Base Insulated Supports

Base Insulated Supports

 

Base Insulated Supports

Base Insulated Supports

PT&P fabricated base insulated supports used to minimize thermal conductivity between the base and un-insulated lines. The support is designed with a carbon steel bottom and a stainless steel upper for cryogenic temperatures of -300°F. The insulation is made of 20 PCF polyurethane block. These supports are designed to handle lateral and axial pipe loads. They also include a wear pad for extra pipe reinforcement, which prevents local deformation of the pipe.

Do you require base insulated supports for project? Let us price them for you today!
request-a-quote


Injection-Molded Anchors for an LNG Plant

June 27th, 2007 No comments
Injection-Molded Anchors for an LNG Plant

Injection-Molded Anchors for an LNG Plant

Injection-Molded Anchors for an LNG Plant

6" NPS Anchors

These supports are used in a re-gasification terminal and are designed for -29°C ambient and -196°C fluid temperatures. The polyurethane foam insulation is injected into a mold with a pipe spool in place to ensure maximum fit. The pipe anchors are made from 516 Grade 70-N carbon steel. These supports were put through Finite Element Analysis and inspected by our Quality Control Department.

Want to learn more about pre-insulated supports? View a pre-insulated support webinar today!


access-our-webinar-archives



Cold Insulated Pipe Anchors for an LNG Plant

June 6th, 2007 No comments
Cold Insulated Pipe Anchors for an LNG Plant

Cold Insulated Pipe Anchors for an LNG Plant

Cold Insulated Pipe Anchors for an LNG Plant

Base Stop

Piping Technology & Products designed and fabricated 36″ diameter insulated pipe anchors that included base stops to prevent lateral and axial movement of the anchor.

The design of the insulated stop plates allows the anchor to withstand 63,000 lbs of axial load. The use of Polyurethane insulation allows for operating temperatures down to -300°F.

Do you require insulated pipe anchors for your piping system? Get pricing today!
request-a-quote


Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy