Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
Pressure Vessels/Tanks — The Pipe Supports Blog

26" Hot Water Expansion Tank for a Compressor Station

September 26th, 2007 No comments

 

 

26" Hot Water Expansion Tank for a Compressor Station

26" Hot Water Expansion Tank for a Compressor Station

26" Hot Water Expansion Tank for a Compressor Station

26″ Hot Water Expansion Tank for a Compressor Station

26″ Hot Water Expansion Tank

– Material: .25″ Thick Carbon Steel
– Design Pressure: 50 PSIG
– Design Temperature: 200 F
– Capacity: 170 Gallons

Do you require a vessel or tank for your current or upcoming job? Get pricing today!
request-a-quote


Categories: Pressure Vessels/Tanks Tags: ,

Pressure Vessel in an Emergency Situation for a Gas Company in Florida

November 8th, 2006 No comments
Pressure Vessel in an Emergency Situation for a Gas Company in Florida

Pressure Vessel in an Emergency Situation for a Gas Company in Florida

– 24″ Diameter Horizontal Pressure Vessel
– Repaired Welds on Flange & Shell
– 12 hr. Turn Around Time
– Hydro-Tested at 1500 PSI
– Held for 1 hr. at 80˚F
– 100% X-Ray

Do you require a pressure vessel or tank for your application? Get pricing today!

request-a-quote


Pressure Vessel for a Chemical Company

April 19th, 2006 No comments
Pressure Vessel for a Chemical Company

Pressure Vessel for a Chemical Company

 

Pressure Vessel for a Chemical Company

Top of Pressure Vessel

This pressure vessel is manufactured from carbon steel SA516-70. Its diameter is 48 by 96 tangent to tangent and weighs 2,140 lbs. The pressure vessel is used as a process feed tank and was painted for rust resistance. In addition, the vessel was designed for pressures at 15 PSIG and temperatures at 86F. Hydro-tests were conducted at 20 PSIG and x-ray tests were completed to ensure quality performance.

Do you require a tank or vessel for your current job? Get pricing now!
request-a-quote


60" Diameter Air Tank for a Manufacturing Facility

July 22nd, 2005 No comments

 

60" Diameter Air Tank for a Manufacturing Facility

60" Diameter Air Tank for a Manufacturing Facility

Side View of Air Receiver Tank

Side View of Air Receiver Tank

Sweco Fab, Inc. recently fabricated an Air Receiver Tank for a Manufacturing Facility in Alabama. This 5,400 lbs tank measured 60″ 143″ tangent to tangent and was designed for 170 PSIG and 200 F. It was fabricated from SA516-70 carbon steel. The interior and exterior were painted with standard epoxy paint to provide an interior lining and exterior protection. The tank was hydrotested at 221 PSIG to ensure product quality.

Want to learn more about products from Sweco Fab? View a past webinar today!


access-our-webinar-archives



Categories: Pressure Vessels/Tanks Tags:

2800 lb. Pressure Vessel for an Oil Refinery

July 9th, 2004 No comments
2800 lb. Pressure Vessel for an Oil Refinery

2800 lb. Pressure Vessel for an Oil Refinery

2800 lb. Pressure Vessel for an Oil Refinery

Close-up of the Explosion Proof Electrical Junction Box

Sweco Fab, Inc. recently designed and fabricated a 2800 lb. pressure vessel for an oil refining company in the United Arab Emirates. This pressure vessel will be used as a dust collector to filter a process fluid for an unleaded gasoline project. The vessel, 30″ in diameter and 14′-11″ OAL, is designed for 150 PSIG and 248°F. Spot radiography, dye-penetrant, and hydrostatic tests were implemented to ensure product quality.

Do you have a requirement for a vessel or tank? Get pricing today!
request-a-quote


108" I.D. x 144" T-T Vessel

August 16th, 2001 No comments
108" I.D. x 144" T-T Vessel

108" I.D. x 144" T-T Vessel

Sweco Fab, Inc., the ASME code fabrication shop for Piping Technology & Products, Inc., specially designed and fabricated a 108″ I.D. x 144″ T-T vessel for the Texas A&M University. The “Aggie Vessel” will be used for special research project at the university. A 24″ T-bolt closure was used for access to the vessel and two stiffner rings were installed to withstand vacuum application. Unique internal design was also applied to facilitate special equipment installation. Helium leak test at 1×10-6 cc/sec will be performed to detect leakage.

Are you in need of a vesssel? Request a quote today!

request-a-quote


48" Diameter x 96" S/S Vertical Carbon Steel Filter Vessels

July 6th, 2001 No comments

 

48" Diameter x 96" S/S Vertical Carbon Steel Filter Vessels

48" Diameter x 96" S/S Vertical Carbon Steel Filter Vessels

48" Diameter x 96" S/S Vertical Carbon Steel Filter Vessels

Vessels

Sweco Fab, the ASME fabrication shop of Piping Technology & Products, Inc., specially designed and manufactured three steel, rubber-lined vessels for a MTBE manufacturer located in Deer Park, TX.

The carbon steel filter vessels were designed with rubber linings in order to help prevent or delay corrosion within. The vessels are 48″ diameter x 96″ s/s vertical and built to ASME. All vessels underwent hydrostatic testing in order to detect leaks (see Figure 2).

Need a vessel for an upcoming project? Get pricing today!

request-a-quote


16’ Dia. x 20’ Carbon Steel Storage Tank

May 11th, 2001 No comments
16’ Dia. x 20’ Carbon Steel Storage Tank

16’ Dia. x 20’ Carbon Steel Storage Tank

Dual cranes are required to lift the pictured 16’ x 20’ Carbon Steel Storage Tank to a flatbed eighteen-wheeler for transportation to the paint yard.Upon completion of painting and lining it will be shipped to a major producer of caustic soda in Corpus Christi, South Texas Area.

This is one of many (similar type) tanks and pressure vessels supplied for a recent plant expansion.

Learn more about tanks and vessels from our webinar archives.




access-our-webinar-archives



Categories: Pressure Vessels/Tanks Tags:

Steam Drums

December 5th, 1994 No comments
Steam Drums

Steam Drums

Sweco Fab, Inc. designed and fabricated several steam drums for the Melamine Project at Donaldsonville, Louisiana.

Want to learn more about our products? Visit our webinar archives today!

access-our-webinar-archives

Categories: Pressure Vessels/Tanks Tags: ,

120” Diameter Carbon Steel Storage Vessel

October 5th, 1994 No comments
120” Diameter Carbon Steel Storage Vessel

120” Diameter Carbon Steel Storage Vessel

Pictured above is a deaerator built by Sweco Fab, Inc. and is destined to go into service for one of the larger chemical companies at their Plaquemine, Louisiana Fields.

The upper vessel shown is a 120” diameter 304L stainless unit connected to a 144” carbon steel storage tank of approximately 38,000 lb.

Do you require a tank or vessel for an upcoming project? Let us price it for you today!

request-a-quote


Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy