These custom instrument supports are fabricated from carbon steel with a hot dipped galvanize finish. The supports vary in heights up to 5′ and widths from 18″ to 24″. A total of 126 stands will be used to support instruments at an oil refinery. PT&P offers a complete line of adjustable and welded instrument supports in various mounting styles.

Do you see a need for instrument supports in a current or future  project of yours? Get pricing today!

These custom heavy duty Fig. 43 yoke u-bolt pipe clamps are designed for manifold piping in a Continuous Catalyst Regeneration plant in Mexico. The yoke clamps are for a 36″ diameter pipe size and are fabricated from A240 Grade 316 stainless steel. They are designed to support a load of 33,731 lb. and temperatures up to 1100°F. PT&P supplied a total of 16 assemblies, comprised of yoke u-bolt clamps and E-type constant springs, for this project.

Do you need yoke u-bolt clamps or constants? We would be happy to provide you with a quote today.

PT&P designed adjustable pipe saddle supports fabricated from A240 Gr 304 stainless steel, for a Booster Pump Station Rehabilitation Project in Florida. The pipe saddles are stanchion type supports designed for 10″ and 16″ pipe sizes, and can be vertically adjusted +/- 3″ by turning the middle section of the seamless pipe.

Looking for adjustable pipe saddles for your application? We’d be happy to serve your needs!

Drawing of Complete Assembly (including hold-down clamp, pedestals and beams)

Pedestals and Beams in Operation

The 54″ suction line carrying gas to a gas compressor at a rate of 1.7 million lb./hr. developed a severe vibration. The deflections in the line were up to 3/4″ and it was fully observable during operation.

Hold-down Clamp in Operation

PT&P designed and manufactured a special elevated hold-down clamp, including a unique laminated vibration dampening lining. The entire pipe hanger assembly stands 22′ high and is coated with a carboline zinc finish. After installation and resumption of operations, the vibrations are now almost imperceptible.

Want to learn more about pipe clamps? View a recording of our pipe clamp webinar now!

Three custom “sling” support assemblies fabricated from stainless steel were designed for an oil refinery in Louisiana. The assemblies are comprised of a 79.25″ diameter custom saddle support and two horizontal travelers (Fig.270 PTP-4). They are capable of loads up to 44,000 lb., and were designed, fabricated and shipped in four weeks for expedited delivery.

Do you have a requirement for a large custom designed product? Get pricing today!

The structural pipe supports are fabricated from carbon steel and coated with red oxide primer. The structural steel will be stored in a warehouse for several months while the power plant is being built. Due to the plant’s location along the United States East Coast, the use of the red oxide primer was selected. Also, modifications were made to our standard “insulation saddles” to allow for a higher load capacity; which can be seen in the foreground of the image above.

Do you require replacement or additional structural supports in your plant? Get a quote today!

The pipe clamps are manufactured from 2″ thick by 10″ wide Chrome-Moly (A387 Gr. 22) bar stock and alloy (A 193 Gr. B7) bolting of 2-3/4″ diameter throughout. They are designed for an operating temperature of 1065°F with a maximum design load rating of 35,000 lb. The pipe clamps will be used to support 24″ diameter pipe in a power plant.

Want to learn more about pipe clamps? Instantly view a past pipe clamp webinar!

22″ Dia. Riser Clamps

All four riser clamps are manufactured from A-36 carbon steel plates and are coated with red oxide primer for rust prevention. They are 22″ in diameter with each plate measuring 2″ thick by 12″ wide by 65″ long. Each riser clamp is capable of supporting loads of up to 38,000 lb. and will be used in a power plant to support “downcomer” lines.

Do you see a need for riser clamps in your current or upcoming project? Let us price them now!

Billet Style Clevis

The clevis and turnbuckle pictured are each fabricated from individual solid pieces of 304H stainless steel. The 304H material, which has a maximum carbon content of 0.06%, was required because these items are designed to be used in an environment with temperatures up to 1000ºF. The customer’s specifications mandated that no welding would be allowed on either the clevises or turnbuckles. Additionally, no forgings were readily available, so blocks of 304H stainless steel were utilized in this design.

Billet Style Turnbuckle

Both the clevises and turnbuckles are made to accommodate rod diameter ranges between 1-1/4″ to 1-3/4″. These components have a maximum load capacity of 18,600 lb. The clevises measure 3″ thick x 5-1/4″ wide x 10-5/8″ tall. The turnbuckles measure 2″ thick x 4″ wide x 9-1/4″ tall. Prior to fabrication, each component was modeled using finite element analysis to determine that stress levels are within the acceptable range.

Do you require some pipe support hardware for your project? Get pricing today!