Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
Support Assembly Components — The Pipe Supports Blog

10" Beam Clamp Assemblies for an Electric Plant in West Virginia

October 17th, 2007 No comments
10" Beam Clamp Assemblies for an Electric Plant in West Virginia

10" Beam Clamp Assemblies for an Electric Plant in West Virginia

10" Beam Clamp Assemblies for an Electric Plant in West Virginia

Beam Clamp

These beam clamp assemblies are fabricated from carbon steel with a hot-dipped galvanized finish. The clamp is designed to support a pipe that is 10″ in diameter and is capable of loads up to 3,600 lb. The rod measures 7/8″ in diameter.

The function of the beam clamp assembly is to support the pipe and allow it to swing. The clamp requires no welding which allows for a quick and easy installation.

Do you require beam clamp assemblies in your project? Get pricing today!


request-a-quote


97" Diameter, 3-Piece Pipe Clamps for a Refinery in Ponca City

July 18th, 2007 No comments
97" Diameter, 3-Piece Pipe Clamps for a Refinery in Ponca City

97" Diameter, 3-Piece Pipe Clamps for a Refinery in Ponca City

Piping Technology & Products, Inc. fabricated 3-piece pipe clamps used to support 97″ diameter stainless steel duct work. This duct work is being added to a refinery for an expansion project in Ponca City, Oklahoma. Each section of the clamp assembly is formed from a continuous plate and gussets are added at each of the bolt locations for increased strength and rigidity. Due to the ducts having a relatively thin wall, these clamps are designed wider than necessary in an effort to reduce localized stresses on the duct work. The lower section of each clamp is formed to create a 150° cradle. This acts as a cradle by supporting the duct without inducing extra pressure, which might cause the duct wall to buckle or bend.

The upper sections are formed from 1/2″ thick by 12″ wide bar stock, whereas the lower sections are formed from 1/2″ thick by 18″ wide. All three sections are rolled to an inner radius of 48 1/2″ and the welded gusset plates are all 1/2″ thick. The upper sections are formed at 105° each, and the upper load bolt is 2″ in diameter while the six clamping bolts are 1 1/2″ in diameter.

The maximum load to be carried by these pipe clamps is 16,888 lb. Each pipe clamp will be used in conjunction with a variable spring support to accommodate movements as high as 2 1/4″.

Do you require 3-piece pipe clamps for your plant or refinery? Get pricing now!
request-a-quote


42" Large Bore Pipe Saddles

June 13th, 2007 No comments
42" Large Bore Pipe Saddles

42" Large Bore Pipe Saddles

42" Large Bore Pipe Saddles

42" Large Bore Pipe Saddles

42" Large Bore Pipe Saddles

42" Large Bore Pipe Saddles

PT&P fabricated 42″ diameter large bore pipe saddles. All pipe saddles are designed to be used on flare lines for a crude expansion project. They are fabricated from A-36 carbon steel and hot dipped galvanized. Sizes range from 16″ – 48″ in diameter and 6″ – 15″ in height.

Do you require large bore pipe saddles in your current project? Get pricing today!
request-a-quote


Pipe Saddles for a Process Plant in Nebraska

April 11th, 2007 No comments
Pipe Saddles for a Process Plant in Nebraska

Pipe Saddles for a Process Plant in Nebraska

Piping Technology & Products, Inc. designed and fabricated pipe saddles for 42″ pipe size. The maximum vertical load is 27,649 lb., axial load is 5,500 lb. and lateral load is 6,040 lb.

Do you see a need for pipe saddles like the one described above? Get pricing today!
request-a-quote


Riser Clamps for a Power Plant in Rhode Island

April 4th, 2007 No comments
Riser Clamps for a Power Plant in Rhode Island

Riser Clamps for a Power Plant in Rhode Island

Riser Clamps for a Power Plant in Rhode Island

Riser Clamp

Piping Technology & Products designed and fabricated 80,000 lb. capacity, Type-3 riser clamps for a power plant in Rhode Island. These riser clamps are designed for a 16″ pipe with 2″ flanges for added support.

Do you see a need for riser clamps in your piping system? Let us price them for you!
request-a-quote


Structural Supports with Megalug Pipe Attachments

December 13th, 2006 No comments
Structural Supports with Megalug Pipe Attachments

Structural Supports with Megalug Pipe Attachments

Structural Supports with Megalug Pipe Attachments

Megalug Attachments

Structural Supports with Megalug Pipe Attachments

Megalug Pipe Attachments

Piping Technology & Products, Inc. Designed and Fabricated Structural Pipe Hangers with Megalug® Pipe Attachments.

Structural Supports with Megalug Pipe Attachments

Structural Supports with Megalug Pipe Attachments

These are carbon steel structural supports designed for 6″, 10″ and 12″ ductile iron pipe. They are hot dip galvanized to protect against corrosion and will be used in conjunction with hydraulic snubbers. The hydraulic snubbers are used to protect against axial shock loading, as well as providing vertical weight support.

Each support utilizes a Megalug pipe attachment to eliminate the need for field welding. The Megalug® attachments are designed to “bite” into the sides of the pipe providing an attachment point for the flanges on the fabricated clamp.

Structural Supports

Structural Supports

The 6″ supports are designed for a maximum vertical load of 3,770 pounds, while the 10″ and 12″ supports are designed for a maximum vertical load of 11,630 pounds. All of the supports are built for an overall height of 55-1/8″ from the upper support steel to pipe centerline.

Want to learn more about our structural supports we offer? Watch a webinar today!


access-our-webinar-archives



80ft. wide Cantilevered Canopy for an International Project

August 9th, 2006 No comments
80ft. wide Cantilevered Canopy for an International Project

80ft. wide Cantilevered Canopy for an International Project

Piping Technology & Products, Inc. fabricated a Cantilevered Canopy for the entrance of an International State Department building. The Canopy was fabricated using ten 20-foot long girders. These girders were connected by sixty-three structural steel members. Together, they formed the 80-foot width of the Canopy. The wooden sheathing and architectural cladding that is supported by the canopy’s inner steel structure was installed at the construction site.

The fabricated girders and structural members combined weight exceeds 33,000 lb.

Piping Technology & Products also supplied the steel framing that supports the sheathing and cladding, roof drains and piping installed inside the canopy.

Want to learn more about the miscellaneous structures we provide? Watch a webinar today!



access-our-webinar-archives



Structural Pipe Hangers for a Pipe Seismic Restraint Project

August 2nd, 2006 No comments
Structural Pipe Hangers for a Pipe Seismic Restraint Project

Structural Pipe Hangers for a Pipe Seismic Restraint Project

Structural Pipe Hangers for a Pipe Seismic Restraint Project in California

Close-Up View of MegaLug

Piping Technology & Products, Inc. and its wholly owned subsidiary, Pipe Shields, Inc. designed and fabricated many structural pipe hangers for an on-going project to rebuild the San Francisco-Oakland Bay Bridge. The pipe hangers are made out of A-36 carbon steel and galvanized to withstand corrosion from the ocean waters and rough winds. These pipe supports will be welded to Pipe Shields’ C Model Anchor Plates, which are set in a cast concrete to the bottom cavity of the bridge.

Structural Pipe Hangers for a Pipe Seismic Restraint Project in California

Structural Pipe Hangers

Supports pictured utilize friction holding devices known as MegaLug®, which permit attachment to the pipes without welding. These supports were designed and fabricated to include improvements in regard to strength and durability to withstand high loads during earthquakes and other seismic events.

Do you see a need for structural pipe hangers in your application? Get pricing now!
request-a-quote


3 Wedge Action Mechanical Joints for a Suspension Bridge

January 25th, 2006 No comments
3 Wedge Action Mechanical Joints for a Suspension Bridge

3 Wedge Action Mechanical Joints for a Suspension Bridge

Three wedge action mechanical joint restraints made of ductile iron materials were utilized to assist in the construction of a suspension bridge. Also, these mechanical joints provide for vertical and axial restraint for the bridge. Each weighs approximately 300 lb. and measures 24” long by 16” wide, and 12” tall for a 6”, 10”, and 12” ductile iron pipe. They are capable of supporting 50,000 lb. In addition, they are designed for seismic conditions with the ability for 7” of axial travel.

Do you require similar supports as those described above? Get pricing today!
request-a-quote


Roller Stands for a Company that Manufactures "Fired Heaters"

December 14th, 2005 No comments
Roller Stands for a Company that Manufactures "Fired Heaters"

Roller Stands for a Company that Manufactures "Fired Heaters"

Roller Stands for a Company that Manufactures "Fired Heaters"
Load Testing Rollers

Roller stands are used to support pipelines that expand and contract longitudinally in the axial direction and where vertical adjustment is not necessary. These roller stands are made of stainless steel and designed for a 26″ pipe. They weigh 160 lbs and are capable of supporting 7,500 lbs. Load testing at 1,000F was completed for performance assurance.

Do you require roller stands like those described above? Get pricing today!

request-a-quote


Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy