Cold Shoe   Pre-Insulated Pipe Supports Online Catalog
  Piping Technology & Products, Inc.
   Contact Us:   info@pipingtech.com   Phone: 713-731-0030   Toll-Free: 800-787-5914

Back Arrow Back to pipingtech.com

 

 Catalog Search 
Catalog Price Request
 First Name *
 
 Last Name *
 
 Company *
 
 Email *
 
 Phone Number *
 
  Items, Descriptions & Quantities *
 

 Catalog Request 

 

Fill out the request form to get your copy today!

 

  Please view our new Pre-Insulated Catalog

Installation & Maintenance Guide


Sliding Insulated Pipe Supports (Hot Shoes and Cold Shoes)

Cold Pipe Shoe

Clean the pipe following the pipe cleaning procedure explained in Note #2. Clean the pipe for the length of the shoe plus 3 inches on either side of where the shoe will be installed.Put the slide plate on the structural support member and center it on the centerline of the pipe. Remove the slide plate and check the surface of structural support member below for bumps or high points. Remove any that are found. Replace the slide plate and weld the mounting plate to the structural support member as shown. Protect PTFE, 25% glass filled, with duct tape or equivalent during welding.Clean the bottom half of the insulation. For Cold Shoes, the polyurethane should be prepared for bonding by sanding it lightly with 60 grit sand paper.

For Cold Shoes apply .042 to .080 inches of wet film thickness of adhesive (Fosters 82-77) to the inside of the insulation, as per manufacturer's instructions.Slide the assembly under the pipe into position above the slide plate which is mounted on the structural support member (See Note #1 for desired location). Note that field trimming of the calcium silicate may be required for proper fit to the pipe circumference.Lower the pipe onto the bottom half of the saddle.Clean the bottom half of the insulation. For Cold Shoes, the polyurethane should be prepared for bonding by sanding it lightly with 60 grit sand paper.For Cold Shoes apply .042 to .080 inches of wet film thickness of adhesive (Fosters 82-77) to the inside of the insulation, as per manufacturer's instructions.Slide the assembly under the pipe into position above the slide plate which is mounted on the structural support member (See Note #1 for desired location). Note that field trimming of the calcium silicate may be required for proper fit to the pipe circumference.Lower the pipe onto the bottom half of the saddle.

Align the clamping holes of the top half to the bottom half of the saddle, and press them together. Seal longitudinal joints and the overlapping ends of the jacket with a suitable sealant such as Foster's Flextra 95-50 or equivalent. Install the clamping bolts, lock washers and nuts. Hand tighten first, check alignment of the saddle and position. When found correct; tighten the nuts applying required torque specified in the drawing.

Cold Pipe Shoe
Cold Pipe Shoe

NOTES:  

1. Cold Setting:

    • For axial cold setting, position the support assembly such that after the support has moved, the centerline of the slide plate approximately matches the centerline of the support.
    • For lateral cold setting, center the support assembly over the slide plate.

 

Cold Pipe Shoe
2. Pipe Cleaning Procedure:
  • The pipe shall be cleaned prior to the application of the adhesive.Carbon steel pipe should be solvent cleaned and allowed to dry.Stainless steel and high alloy pipes which have been primed shall have the primer roughened with hand tool or power tool, followed by solvent cleaning.
  • When used in cryogenic applications (below –40ºF), the metal surface must be sand blasted or primed with polyamide epoxy primer.
   
   

Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy