Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
The Pipe Supports Blog

Refractory Lined Pre-Insulated Supports

June 18th, 2008 No comments
Refractory Lined Pre-Insulated Supports

Refractory Lined Pre-Insulated Supports

Refractory Lined Pre-Insulated Supports

Shipping Pre-Insulated Supports

Piping Technology & Products, Inc. designed and fabricated rotational anchor pre-insulated pipe supports for a fluid processing plant in Kuwait. The supports range in size from 24″ to 34″ in diameter and are capable of withstanding 12,500 lb. of vertical load. The bottom of the hot shoe is fabricated from carbon steel and the top from stainless steel.

These supports include stainless steel inner thrust plates that function as an anchor to prohibit the pipe from rotating within the shoe. These supports are designed for steam super heater lines and provide thermal insulation for the pipe in order to prevent heat loss and condensation.

Want to learn more about pre-insulated supports? Instantly watch a pre-insulated support webinar!
access-our-webinar-archives

48" Carbon Steel Pressure Vessel

June 5th, 2008 No comments
48" Carbon Steel Pressure Vessel

48" Carbon Steel Pressure Vessel

Pressure Vessel
– Diameter: 48″ O.D.
– Capacity: 1,100 Gallons
– Material Fabricated From: Carbon Steel
– Design Temperature & Pressure: 285 PSIG at 100ºF
– Testing: Hydro-Tested and held for 1/2 hour at 428 PSIG

Do you have a need for a pressure vessel? Get pricing on a vessel today!

request-a-quote

8 Foot Long Big Ton Variable Spring Assembly

May 28th, 2008 No comments

8 Foot Long Big Ton Variable Spring Assembly

8 Foot Long Big Ton Variable Spring Assembly

8 Foot Long Big Ton Variable Spring Assembly

Slideplates on Big Ton Spring Assembly

This big ton spring assembly is designed for a local area refinery, and is fabricated from carbon steel components with a painted finish. The top of the load flange has three PTFE, 25% glass filled slide plates. The base is 96″ x 18″ and the installed height is 24″. This big ton spring will be utilized to support heavy (in excess of 76,000 lb.) loads where a standard variable spring would be undersized. The big ton spring design includes an array of parallel coils within one frame to produce large load carrying capacity while maintaining the same spring rate. The assembly is designed to withstand an operating load of 76,800 lb. and has a downward travel of 0.894″.

Prior to fabrication, each of the coils were individually tested to insure correct spring rate and load capacity. After fabrication, the entire assembly was tested throughout the entire load and travel range.

Want to learn more about big ton springs? View an engineered spring support webinar today!


access-our-webinar-archives



7 Foot Long Pressure Vessel for a Chemical Plant

May 14th, 2008 No comments
7 Foot Long Pressure Vessel for a Chemical Plant

7 Foot Long Pressure Vessel for a Chemical Plant

This pressure vessel measures 84″ in length and is fabricated entirely of SA516-70 carbon steel. It is designed for low temperature environments and has a design pressure of 117 PSIG at 500ºF. A hydrostatic test was completed at 205 PSIG prior to shipment.

Do you have a requirement for a pressure vessel in your plant? Get pricing today!
request-a-quote

10 Feet Long Graphite Slide Plates for a Plant in Alberta

May 7th, 2008 No comments
10 Feet Long Graphite Slide Plates for a Plant in Alberta

10 Feet Long Graphite Slide Plates for a Plant in Alberta

The top sheet of graphite measures 1/2″ x 11 1/2″ x 115 1/2″. This particular design also includes a bottom sheet of graphite with the same dimensions, but only 1/4″ thick. Each individual graphite sheet is bonded to a hot dipped galvanized backing plate with a 1/2″ lip all around for full welding. In an application where the pipe has large amount of movement due to thermal expansion, slide plates can be utilized to eliminate friction between the pipe support and the supporting member. Graphite is used when the slide plate must function at high temperatures. These particular graphite slide plates are designed for 1000ºF.

Want to learn more about slides plates? View a recording of a past slide plate webinar today!
access-our-webinar-archives

Categories: Slide Plates Tags: ,

90" O.D. Duct Work for an Ammonia Plant

April 25th, 2008 No comments

90" O.D. Duct Work for an Ammonia Plant

90" O.D. Duct Work for an Ammonia Plant

90" O.D. Duct Work for an Ammonia Plant

90" O.D. Duct Work for an Ammonia Plant

The duct work has an outside diameter of 90 inches and is 38 feet long. The duct assembly is fabricated entirely from ASTM A516-70 carbon steel. The assembly has two support bases and stiffening rings that provide strength and rigidity for the duct work. The assembly is a section of air supply duct in an Ammonia Plant.

Do you require duct work for your piping system? Get pricing today!
request-a-quote

63″ x 63″ Big Ton Springs for an Oil Refinery

April 14th, 2008 No comments
63" x 63" Big Ton Springs for an Oil Refinery

63" x 63" Big Ton Springs for an Oil Refinery

The base measures 63 inches square while the top load flange measures 55 inches square. One of the springs has an overall height of 22-7/16″ and the other an overall height of 28-5/8″. Both big ton springs are custom designed and fabricated from carbon steel with a hot-dipped galvanized finish. The top of the load flange is covered by a stainless steel slide plate. These big ton springs will be used to support heavy (in excess of 100,000 lb.) loads where a standard variable spring would be undersized.

One of the big ton springs is designed with a operating load of 126,000 lb. and the other with an operating load of 225,000 lb. Prior to fabrication, all of the coils, within the frame, were individually tested to insure correct spring rate and load capacity. After the units are fabricated, the entire assembly is tested throughout the entire load/travel range.

Do you require a similar spring support in your piping system?  Let us price it for you now! 
request-a-quote

Polyurethane Saddle Supports for FRP Pipe

April 2nd, 2008 No comments
Polyurethane Saddle Supports for FRP Pipe

Polyurethane Saddle Supports for FRP Pipe

Polyurethane Saddle Supports for FRP Pipe

Polyurethane Saddle Supports for FRP Pipe

Piping Technology & Products, Inc. designed and fabricated these saddle supports to support FRP pipe or similar plastics in sizes from 2″ to 36″ in diameter. The saddle support is fabricated from a molded density 20 polyurethane block with a load bearing capacity of 150 PSI that allows for high loads for a 36″ diameter line.

The base is bonded to a 20 gauge steel pan that provides a steel to steel resting surface. The foam is extended on each side of the base to allow field strapping of the support to the pipe. These saddle supports are often used in a circulating water service. These particular supports are to be used in a power generating station in the U.S.

Do you require similiar saddle supports for your application? Let us price them for you!
request-a-quote

Permali® Cold Shoes for Carbon Steel Pipe

March 12th, 2008 No comments
Permali® Cold Shoes for Carbon Steel Pipe

Permali® Cold Shoes for Carbon Steel Pipe

These cold shoes are anchors supports and fabricated with A-36 carbon steel and permali® block insulation. The carbon steel is hot-dipped galvanized for protection and longevity of the cold shoe. The permali® block insulation, between the base plate and the saddle, functions to insulate the supporting structure from extreme cold temperatures of the pipe.

These cold shoes are designed for pipes ranging in size from 6″ to 14″. The assemblies are capable of loads ranging from 194,000 lb. to 291,000 lb.

Want to learn more about pre-insulated supports? Instantly view a past webinar today!


access-our-webinar-archives



140,700 lb. Load Hydraulic Snubbers

March 5th, 2008 No comments
140,700 lb. Load Hydraulic Snubbers

140,700 lb. Load Hydraulic Snubbers

140,700 lb. Load Hydraulic Snubbers

Side View of Snubber

Anchor/Darling Enterprises, Inc., a wholly owned subsidiary of Piping Technology & Products, Inc. designed and fabricated these hydraulic snubbers for a power plant in Turkey. They are adjustable type snubbers with two rear brackets. The hydraulic snubbers can absorb loads up to 140,700 lb.

Design:

Temperature: 375°F
Pressure: 1,750 PSIG
Stroke: 6″

Do you see a need for snubbers in your piping system? Get pricing today!
request-a-quote

Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy