Piping Technology and Products Logo

Piping Technology & Products

Loading
 
  Experienced Manufacturer of Pipe Supports since 1978
Call Us: (713) 731-0030 Toll-Free: (800) 787-5914   Se habla español
 
Pipe Clamp — The Pipe Supports Blog

Custom Designed Pipe Clamp and Sway Strut Assemblies for an Ethane Cracker Facility in Texas

December 12th, 2016 Comments off

Custom Designed Pipe Hanger and Pipe Clamp Assemblies for an Ethane Cracker Facility in Texas

Type: Pipe Clamp and Sway Strut Assemblies
Design: Operating load: 99,650 lb. | Temperature: 550°F
Material: A36 Carbon Steel
Size: Clamps: 149″ L x 14″ W x 2″ T | Load Bolt: 4-1/2″ | 68″ Dia. Pipe

Piping Technology & Products custom designed pipe clamp and sway strut assemblies assemblies for an ethane cracker facility in Texas. The clamps are designed for a 68″ diameter pipe using a bar size of 149″ long x 14″ wide x 2″ tall. The load bolt size is 4-1/2″ and the inside bolts, rods, nuts, and turnbuckle are 4″ diameter. The assemblies are completely fabricated from A36 carbon steel, and designed for an operating temperature of 550°F with a load capacity up to 99,650 lb. A visual inspection test with sample pipe and dimensional check were conducted prior to shipment.

Sway Strut and Pipe Clamp Assemblies Designed for an Energy Combustibles and Lubricants Facility

November 18th, 2016 Comments off

Sway Struts with Pipe Clamps for Energy Combustibles and Lubricants Facility in Argentina

Type: Sway Strut and Pipe Clamp Assemblies
Design: 4,500 lbs load
Material: A-36 Carbon Steel
Function: Let the pipe sway within a certain radius

Piping Technology & Products designed these Fig.2110F sway struts and pipe clamp assemblies for an energy combustibles and lubricants facility in Argentina. The sway struts are 60″ in length with clamp sizes of 16″ and 12″ diameters. All components were fabricated from A-36 carbon steel. They are designed for an operating load of 4,500 lb. The sway struts are designed to let the pipe sway within a certain radius.

14” Diameter Pipe Clamp Assemblies Designed and Manufactured by PT&P for a Refining Project in Saudi Arabia

July 11th, 2016 Comments off

14” Diameter Pipe Clamp Assemblies Designed and Manufactured by PT&P for a Refining Project in Saudi Arabia

Piping Technologies & Products fabricated these special designed Split-T pipe shoes using a Figure 50 “two-bolt pipe clamp” for a refining project in Saudi Arabia.  The pipe shoes are 4″ height x 15.5″ wide x 18″ long and were fabricated from A36 carbon steel with a hot-dipped galvanized finish.  They are designed for a pipe size of 14″ with an operating temperature from -29°C to 316°C. The pipe shoes are capable of supporting an operating load of 34,000 lb.

Pipe Clamp Assemblies Custom Designed for a Partial Oxidation Unit in a Synthetic Gas Plant

August 9th, 2015 Comments off

Pipe Clamp Assemblies Custom Designed for a Partial Oxidation Unit in a Synthetic Gas Plant

PT&P custom designed pipe clamp assemblies for a partial oxidation unit in a synthetic gas plant located in Texas. The pipe clamps were fabricated from alloy A387 and coated with a special paint for high temperatures. The assemblies were designed with supportive structures for pipe sizes ranging from 2″ to 16″. Standard quality control inspection and tests were conducted prior to shipment.

Custom Designed Pipe Hanger & Clamp Assemblies for a Flue-gas Desulfurization Application

June 29th, 2015 Comments off

Custom Designed Pipe Hanger & Clamp Assemblies for a Flue-gas Desulfurization Application

PT&P custom designed pipe hanger and clamp assemblies for a flue-gas desulfurization application in an energy facility located in Kansas. The assemblies are designed for pipes ranging in size from 2-1/2″ to 6″ in diameter, and are capable of a 650 lb. operating load. Materials include tube steel, fig. 92 washer, fig. 122 all threaded rod, fig. 30 turnbuckle, fig. 40 weldless eyenut and fig. 70 pipe clamp.

114″ Diameter, 3-Piece Pipe Clamp and Sway Strut Assembly

July 18th, 2011 No comments

114" Diameter 3-Piece Pipe Clamp

The 114″ diameter, 3-piece pipe clamp is fabricated from A36 carbon steel and the pins are stainless steel. The sway strut is also fabricated from carbon steel and measures 24′-8″ long. This assembly can support loads up to 27,200 lb. and will be used in an oil refinery in Louisianna.

Sway Strut Assembly

 

Do you require clamps or sway struts for an upcoming project? We’d be happy to serve your needs! request-a-quote

Custom Constant Spring Hangers and Pipe Clamps

June 8th, 2010 No comments
Custom Constant Spring Hangers and Pipe Clamps

Custom Constant Spring Hangers and Pipe Clamps

The constant spring hangers are manufactured from A36 carbon steel and have custom 4-bolt pipe clamps due to heavy loads. The dimensions are 40″ length x 18″ width x 85″ height and are designed for a 1,784 lb. load with 10″ of travel. The constants will be used to support radiant inlet manifolds and have a unique paint applied due to the highly corrosive condition. The entire pipe hanger assembly went through load and travel testing prior to shipping.

Want to learn more about constant springs? Instantly view a past constant webinar!
access-our-webinar-archives

68,000 lb. Load Custom Clamp

September 10th, 2008 No comments
68,000 lb. Load Custom Clamp

68,000 lb. Load Custom Clamp

68,000 lb. Load Custom Clamp

Custom Clamp

This custom pipe clamp will be used in conjunction with a hydraulic snubber to restrain pipe movement during extremely high disturbances. It is designed to support the pipe where two heavy duty flanges join. The yoke, lugs, and strap sections of the clamp are carbon steel, and the clamp bolts and load bolt/pin are stainless steel.

The outer diameter of the clamp section is 16″, and the inner diameter is 10″. The upper lugs are fabricated from 3/4″ thick plate with a 2-1/4″ diameter load bolt. The maximum load for this custom clamp is 68,000 lb.

Do you require custom pipe clamps in your piping system? Get pricing today!
request-a-quote

10" Beam Clamp Assemblies for an Electric Plant in West Virginia

October 17th, 2007 No comments
10" Beam Clamp Assemblies for an Electric Plant in West Virginia

10" Beam Clamp Assemblies for an Electric Plant in West Virginia

10" Beam Clamp Assemblies for an Electric Plant in West Virginia

Beam Clamp

These beam clamp assemblies are fabricated from carbon steel with a hot-dipped galvanized finish. The clamp is designed to support a pipe that is 10″ in diameter and is capable of loads up to 3,600 lb. The rod measures 7/8″ in diameter.

The function of the beam clamp assembly is to support the pipe and allow it to swing. The clamp requires no welding which allows for a quick and easy installation.

Do you require beam clamp assemblies in your project? Get pricing today!


request-a-quote


97" Diameter, 3-Piece Pipe Clamps for a Refinery in Ponca City

July 18th, 2007 No comments
97" Diameter, 3-Piece Pipe Clamps for a Refinery in Ponca City

97" Diameter, 3-Piece Pipe Clamps for a Refinery in Ponca City

Piping Technology & Products, Inc. fabricated 3-piece pipe clamps used to support 97″ diameter stainless steel duct work. This duct work is being added to a refinery for an expansion project in Ponca City, Oklahoma. Each section of the clamp assembly is formed from a continuous plate and gussets are added at each of the bolt locations for increased strength and rigidity. Due to the ducts having a relatively thin wall, these clamps are designed wider than necessary in an effort to reduce localized stresses on the duct work. The lower section of each clamp is formed to create a 150° cradle. This acts as a cradle by supporting the duct without inducing extra pressure, which might cause the duct wall to buckle or bend.

The upper sections are formed from 1/2″ thick by 12″ wide bar stock, whereas the lower sections are formed from 1/2″ thick by 18″ wide. All three sections are rolled to an inner radius of 48 1/2″ and the welded gusset plates are all 1/2″ thick. The upper sections are formed at 105° each, and the upper load bolt is 2″ in diameter while the six clamping bolts are 1 1/2″ in diameter.

The maximum load to be carried by these pipe clamps is 16,888 lb. Each pipe clamp will be used in conjunction with a variable spring support to accommodate movements as high as 2 1/4″.

Do you require 3-piece pipe clamps for your plant or refinery? Get pricing now!
request-a-quote


Mailing: P.O. Box 34506, Houston, TX 77234-4506 Location: 3701 Holmes Road, Houston, TX 77051
Our Subsidiaries: U.S. Bellows: Metallic & Fabric Expansion Joints, Bellows
Sweco Fab: ASME Vessels, Pig Launchers, Spectacle Blinds
 Pipe Shields: Pre-Insulated Pipe Supports, Slides, Guides & Anchors

Fronek Anchor/Darling
: Snubbers, Sway Struts & Sway Braces
Phone: (713) 731-0030 Toll-Free: (800) 787-5914 FAX: (713) 731-8640 info@pipingtech.com

©2017 Piping Technology and Products, Inc. All Rights Reserved. Contact Us | Privacy Policy